inductors january 2015 wound ferrite nlc453232 4532 [1812 inch]* * dimensions code jis[eia] inductors for decoupling circuits nlc453232 ty p e nlc series
(2/10) inductors 20150105 / inductor_commercial_decoupling_nlc453232_en.fm reminders for using these products before using these products, be sure to request the delivery specifications. safety reminders please pay sufficient attention to the warnings for safe designing when using these products. the storage period is less than 6 months. be sure to follow the storage conditions (temperature: 5 to 40c, humidity: 10 to 75 % rh or less). if the storage period elapses, the soldering of the terminal electrodes may deteriorate. do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). before soldering, be sure to preheat components. the preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150c. soldering corrections after mounting should be within the range of the conditions determined in the specifications. if overheated, a short circuit, performance deterioration, or lifespan shortening may occur. when embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. self heating (temperature increase) occurs when the power is turned on, so the tolerance should be sufficient for the set therm al design. carefully lay out the coil for the circuit board design of the non-magnetic shield type. a malfunction may occur due to magnetic interference. use a wrist band to discharge static electricity in your body through the grounding wire. do not expose the products to magnets or magnetic fields. do not use for a purpose outside of the contents regulated in the delivery specifications. the products listed on this catalog are intended for use in general electronic equipment (av equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. the products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. if you intend to use the products in the applications listed below or if you have special requirements exceeding the range or c onditions set forth in the each catalog, please contact us. (1) aerospace/aviation equipment (2) transportation equipment (cars, electric trains, ships, etc.) (3) medical equipment (4) power-generation control equipment (5) atomic energy-related equipment (6) seabed equipment (7) transportation control equipment (8) public information-processing equipment (9) military equipment (10) electric heating apparatus, burning equipment (11) disaster prevention/crime prevention equipment (12) safety equipment (13) other applications that are not considered general-purpose applications when designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securi ng protection circuit/device or providing backup circuits in your equipment. reminders
(3/10) inductors 20150105 / inductor_commercial_decoupling_nlc453232_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. inductors for decoupling circuits wound ferrite features resin mold type wound induct or for decoupling circuits. e-12 series, wide lineup compatible with k (10%) tolerance allows for various usages. application smart meters, av equipment, xdsl, electronic devices for communications infrastruct ure such as mobile base stations, industrial equipment, other part number construction operating temperature range, pack age quantity, product weight operating temperature range includes self-temperature rise. the storage temperature range is for after the circuit board is mounted. product compatible with rohs directive compatible with lead-free solders overview of nlc453232 type nlc 453232 t - 1r0 k - pf series name lwh dimensions packaging style inductance inductance tolerance lead-free compatible (mm) (h) 453232 4.53.23.2 t taping 1r0 1 k 10% 100 10 101 100 type temperature range package quantity individual weight operating temperature c storage temperature c (pieces/reel) mg nlc453232 C40 to +105 C40 to +105 500 180 rohs directive compliant product: see the following for more details related to rohs directive compliant products. http://produ ct.tdk.com/en/environment/rohs/
(4/10) inductors 20150105 / inductor_commercial_decoupling_nlc453232_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. nlc453232 type recommended reflow profile preheating soldering peak temp. time temp. time temp. time t1 t2 t1 t3 t2 t4 t3 150c 180c 90 to 120s 230c 40s 255c 10s max. natural cooling t3 t1 preheating t2 soldering t3 t3 t4 t2 t1 t: time peak t: temperature
(5/10) inductors 20150105 / inductor_commercial_decoupling_nlc453232_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. nlc453232 type shape & dimensions recommended land pattern dimensions in mm 120 r0.2 c0.5 4.50.3 3.20.2 3.20.2 2.60.1 0.5 ( 3.3 )( 0.6 ) ( 0.6 ) dimensions in mm 2.8 1.5 3 1.5
(6/10) inductors 20150105 / inductor_commercial_decoupling_nlc453232_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. nlc453232 type electrical characteristics characteristics specification table rated current: smaller value of either idc1 or idc2. idc1: when based on the inductance change rate (10% below the initial l value) idc2: when based on the temperature increase (temperature increase of 20c by self heating) measurement equipment ? equivalent measurement equipment may be used. l q l, q measuring frequency dc resistance rated current part no. (h) tolerance min. (mhz) ( )max. (ma)max. 1 10% 10 7.96 0.11 1050 nlc453232t-1r0k-pf 1.2 10% 10 7.96 0.12 1000 nlc453232t-1r2k-pf 1.5 10% 10 7.96 0.15 950 nlc453232t-1r5k-pf 1.8 10% 10 7.96 0.16 900 nlc453232t-1r8k-pf 2.2 10% 10 7.96 0.18 850 NLC453232T-2R2K-PF 2.7 10% 10 7.96 0.2 800 nlc453232t-2r7k-pf 3.3 10% 10 7.96 0.22 750 nlc453232t-3r3k-pf 3.9 10% 10 7.96 0.24 700 nlc453232t-3r9k-pf 4.7 10% 10 7.96 0.27 650 nlc453232t-4r7k-pf 5.6 10% 10 7.96 0.3 650 nlc453232t-5r6k-pf 6.8 10% 10 7.96 0.35 600 nlc453232t-6r8k-pf 8.2 10% 10 7.96 0.4 600 nlc453232t-8r2k-pf 10 10% 10 2.52 0.5 550 nlc453232t-100k-pf 12 10% 10 2.52 0.6 500 nlc453232t-120k-pf 15 10% 10 2.52 0.7 450 nlc453232t-150k-pf 18 10% 10 2.52 0.8 400 nlc453232t-180k-pf 22 10% 10 2.52 0.9 370 nlc453232t-220k-pf 27 10% 10 2.52 1.2 330 nlc453232t-270k-pf 33 10% 10 2.52 1.4 300 nlc453232t-330k-pf 39 10% 10 2.52 1.6 280 nlc453232t-390k-pf 47 10% 10 2.52 1.9 260 nlc453232t-470k-pf 56 10% 10 2.52 2.2 240 nlc453232t-560k-pf 68 10% 10 2.52 2.6 220 nlc453232t-680k-pf 82 10% 10 2.52 3.5 200 nlc453232t-820k-pf 100 10% 20 0.796 4 180 nlc453232t-101k-pf 120 10% 20 0.796 4.5 160 nlc453232t-121k-pf 150 10% 20 0.796 6.5 140 nlc453232t-151k-pf 180 10% 20 0.796 7.5 120 nlc453232t-181k-pf 220 10% 20 0.796 9 120 nlc453232t-221k-pf 270 10% 20 0.796 11 100 nlc453232t-271k-pf 330 10% 20 0.796 13 90 nlc453232t-331k-pf measurement item product no. manufacturer l, q 4194a+16085a+16093b agilent technologies dc resistance vp-2941a panasonic
(7/10) inductors 20150105 / inductor_commercial_decoupling_nlc453232_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. nlc453232 type electrical characteristics l frequency characteristics graph measurement equipment ? equivalent measurement equipment may be used. 0.1 10 1 100 0.01 0.1 10000 100 1000 1 10 frequency ( mhz ) inductance ( h ) 331k 271k 221k 181k 151k 121k 101k 680k 560k 470k 390k 270k 220k 150k 3r9k 8r2k 100k 120k 4r7k 5r6k 6r8k 3r3k 2r7k 1r0k 2r2k 1r8k 1r5k 1r2k 820k 180k 330k product no. manufacturer 4294a agilent technologies
(8/10) inductors 20150105 / inductor_commercial_decoupling_nlc453232_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. nlc453232 type electrical characteristics inductance vs. dc bias characteristics graph measurement equipment ? equivalent measurement equipment may be used. 0.01 0.1 1 10 0.1 10 1 100 1000 dc current ( a ) inductance ( h ) 331k 271k 221k 181k 151k 121k 101k 820k 680k 560k 470k 390k 330k 270k 220k 180k 150k 120k 100k 8r2k 6r8k 5r6k 4r7k 3r9k 3r3k 2r7k 2r2k 1r8k 1r5k 1r2k 1r0k product no. manufacturer 4285a+42841a+42842c agilent technologies
(9/10) inductors 20150105 / inductor_commercial_decoupling_nlc453232_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. nlc453232 type electrical characteristics impedance frequency characteristics graph measurement equipment ? equivalent measurement equipment may be used. 0.1 10 1 100 0.1 1000000 100000 100 1000 10000 1 10 impedance ( ) frequency ( mhz ) 331k 271k 221k 121k 101k 181k 151k 560k 470k 220k 270k 180k 680k 390k 330k 150k 4r7k 5r6k 8r2k 3r9k 3r3k 1r0k 6r8k 100k 120k 2r2k 1r8k 1r5k 1r2k 2r7k 820k product no. manufacturer 4294a agilent technologies
(10/10) inductors 20150105 / inductor_commercial_decoupling_nlc453232_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. nlc453232 type packaging style reel dimensions * these values are typical values. tape dimensions ty p e a w1 w2 n e nlc453232 ?180 13 17 ?60 0.5 ?13.0 0.5 ?21.0 0.8 2.0 0.5 a ( 1.0 ) dimensions in mm n e w2 w1 fe w p0p2?d0 p1 a t b k dimensions in mm ty p e a b ?d0 e f p0 p1 p2 w k t nlc453232 3.6 4.9 1.5+0.1/-0 1.750.1 5.500.05 4.000.10 8.000.10 2.000.05 12.00.30 3.2 0.4
|
